|
|
|
The following copyrighted silver care information has been provided by Jeffrey Herman, Herman Silver
Restoration & Conservation. None of the below guide can be reproduced without written permission from
Jeffrey Herman, PO Box 72839, Providence,
RI 02970, 401/461-6840, jeffherman@silversmithing.com
Silver Repair Advice
- Dishwashers will eventually turn silver white from heat and harsh detergents, requiring professional refinishing.
- Silverware, when used on a daily basis, will require no polishing. Make sure to hand wash the pieces with a
phosphate free detergent and dry them immediately to avoid spotting.
- Salt is extremely corrosive to silver; always empty shakers and wash them when not used on a regular basis.
- Candelabra arms must always be supported from underneath to avoid distortion or possible breakage.
- Before using a restoration service, get recommendations from parap creations.
Monogram Removal
A hand engraved monogram or any type of decorative engraving is part an object's history and unique to that piece.
Removing engraving does not always make a piece more salable, especially if the engraving is of high quality--quality
seldom seen today with the declining number of outstanding engravers.
Some tips for collectors and antique dealers debating whether or not to have engraving removed: (1.) If it is a tray or
hollow piece, rub your fingernail under or inside to determine if the metal is thick enough to have the engraving removed.
If you see a slight wave develop as you move your fingernail, the piece is probably too thin. Remember, if the engraving
is removed you run the risk of caving in that area with very little pressure. Can you imaging setting a coffee pot on a
footed salver and having it sink into the center? (2.) If you have never used a repair service, test the reliability of the
silversmith with a small piece of damaged flatware first. A competent smith will do a great job or suggest that the repair
not be attempted at all. (3.) If engraving is removed from a hollow form or tray and you would like it reengraved, have
it done in a different area where the material is thicker. An engraved area, especially on a thin piece, will be rather weak.
If you must have engraving removed, take the piece to a competent smith, otherwise it may be ruined and the piece
devalued. Engraving that has been expertly removed will be undetectable on the surface. Upon removal of deep
engraving, on a coffee pot for example, the metal may have to be pushed out from the inside to develop a level surface.
Candlestick/Candelabra Thread Repair
Over the years, weighted candlestick and candelabra threaded inserts can become worn, allowing them to continue
rotating in the corresponding sockets without properly “catching.” Redefining these threads properly can be quite costly,
since the pitch that is used as a reinforcing cement must be removed before pushing out the threads from inside with special tools.
In most cases, you can repair the insert threads yourself, allowing them to fully engage the corresponding socket threads.
Go to your local hardware store or furnace and duct supplier and ask for aluminum tape. This is aluminum foil with an
extremely sticky backing. Take the section with the worn threads and cut a piece of aluminum tape the same width as the
threaded section. Remove the backing and wrap the aluminum around the threaded insert and cut it as close as possible to
meet with the other edge. It’s better to be a little undersize than have to overlap the seam.. Next, use finger pressure to
massage the foil securely onto the insert. Finish the job by using your fingernail to trace the threads around the circumference
of the insert, making them more distinct.
Gently screw the insert into the socket, testing how it “sits” without wobbling. If there is still substantial play in the socket,
allowing the insert to continue spinning, wrap it with another layer of tape as described above.
Leveling a Hinged Lid
Teapots, coffeepots, boxes, ink wells, and anything with a hinged top, may become unsettled in the way they sit due to
rough treatment. Perhaps you have a piece with a springy top that simply won't sit level. You may be able to rectify this
problem yourself. Cut to length and place a flat toothpick between the entire length of the two hinge plates and push, ever
so gently, on the sides of the lid with your fingers. Take notice of any movement on the back side of the lid where the hinge
palate is attached. If the lid still doesn't sit level, repeat the process by stacking additional toothpicks between the hinge plates.
Disposal Damaged Flatware
Has a piece of your flatware ever slipped down the garbage disposal? If so, you may have gone into shock in regard to its
mangling. The spoon bowl may have been crushed, fork tines wrapped around each other, the handle folded in half or even
chopped into many pieces. A monogram may also have been gouged. That piece of flatware, with the possible exception of
hollow handled knives, need not be taken to the refiner; it most likely can be repaired to a functional state!
In order to correct the shape and finish of the piece during its repair, it is recommended to send a perfect duplicate piece for
matching. Flatware that is highly ornamental, especially on the handles, may not be economical to restore. In this case you may
wish to simply have any sharp or jagged edges smoothed to make the piece useful once again.
If you feel the piece doesn't warrant the repair expense, it can most likely be replaced through a silver replacement service.
Since many patterns over time have been produced in different weights, it is best send a sample to the service to be matched.
| |
|